- 论坛徽章:
- 0
|
本帖最后由 lbseraph 于 2014-05-23 17:05 编辑
请教:
弄了台4640想学习,安装rhel一切正常,装ux就报这个I/O error
* Installing fileset "Networking.100BT-KRN,r=B.11.31" (15 of 2173).
* Installing fileset "Networking.INTL100-KRN,r=B.11.31" (16 of 2173).
* Installing fileset "Networking.NMS2-KRN,r=B.11.31" (17 of 2173).
* Installing fileset "Networking.PPP2-KRN,r=B.11.31" (18 of 2173).
* Installing fileset "Networking.NW-ENG-A-MAN,r=B.11.31" (19 of 2173).
* Installing fileset "Networking.LAN-PRG,r=B.11.31" (20 of 2173).
* Installing fileset "Networking.NET-RUN-64,r=B.11.31" (21 of 2173).
* Installing fileset "Networking.NET-PRG,r=B.11.31" (22 of 2173).
* Installing fileset "Streams.STREAMS2-RUN,r=B.11.31" (23 of 2173).
* Installing fileset "Streams.STREAMS-RUN,r=B.11.31" (24 of 2173).
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296662, 8192 bytes of 8192 bytes not paged, page addr =dead31.e00000013988a000, bflag =40000f, bp = e000000155385380
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone": I/O error (5). Cannot copy it to file "/usr/conf/mod/clone".
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296672, 8192 bytes of 8192 bytes not paged, page addr =dead31.e00000013988a000, bflag =40000f, bp = e000000155385380
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296680, 8192 bytes of 8192 bytes not paged, page addr =dead31.e000000139884000, bflag =40000f, bp = e000000155385c80
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo": I/O error (5). Cannot copy it to file "/usr/conf/mod/echo".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/ffs": I/O error (5). Cannot copy it to file "/usr/conf/mod/ffs".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31". Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo": Error 0 (0). Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31". Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo": Error 0 (0). Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31". Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo": Error 0 (0). Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31". Check the above output for details.
ERROR: The Install Phase has suspended.
ERROR: Aborting the Install Phase.
NOTE: More information may be found in the Software Manager logfile using the command "swm job log -v 000001".
======= 01/01/98 01:38:19 UTC END Software Install failed with 15 errors. (user=root) (jobid=000001)
ERROR: Software load had one or more errors.
======= 01/01/98 01:38:19 UTC The operating system software has not been successfully loaded. The swm install(1M) application was not completed or failed to load
some key files. (exit status was = 1).
1: Change the install server and/or depot information.
2: Retry software load process (non-interactive mode).
3: Retry software load process (interactive mode).
4: Run a shell.
|
|